Recent advancements in Global Navigation Satellite System-Interferometric Reflectometry (GNSS-IR) have enabled the extraction of environmental data by analyzing differences between direct and multipath signals. A key application is soil moisture estimation using Signal-to-Noise Ratio (SNR) measurements of reflected signals. However, these methods only provide relative moisture estimates, requiring periodic in-situ measurements to establish the minimum moisture level for each observation period. On the other hand, optical remote sensing estimates soil moisture through pixel reflectance, clearing the need for in-situ measurements but is limited by sensitivity to weather and illumination conditions, cloud cover, ground vegetation cover, and a 3–5-day satellite orbit, hindering continuous estimation. This study further develops the potential of GNSS-IR for soil moisture estimation by introducing a novel, optimized approach to enhance accuracy. We also develop a data fusion model that combines GNSS-IR's continuous, weather-independent measurements with discrete estimates from spectral remote sensing Sentinel-2 imagery. This model enables continuous soil moisture estimation without in-situ measurements. We use datasets from Valencia, Spain, and Kabri, Israel, to evaluate the methodology. Our models achieve an accuracy relative to in-situ data of approximately 0.02 [m3/m3] in soil moisture estimation, outperforming traditional methods, which have an accuracy of around 0.05 [m3/m3].
}
In relative GNSS surveying, the accuracy of the vector solution is influenced by measurement conditions such as baseline length, atmospheric effects, satellite geometry, and environmental obstructions. To ensure high accuracy under challenging conditions, surveyors often apply constraints such as static positioning or control point initialization. These practices, while effective, typically rely on empirical judgment that result in longer measurement times to ensure reliability. Alternatively, integrated systems such as INS/GNSS can introduce real-time motion-based constraints that may optimize measurement time without compromising accuracy. Despite the known potential of such constraints, no comprehensive study has assessed their contribution to the GNSS vector solution using a statistically rigorous and generalizable approach. This study proposes a novel analytical framework for evaluating the contribution of geometric constraints to GNSS vector solutions, based on a closed-form mathematical formulation and a realistic stochastic model. The model enables quantification of the constraints’ effects on both accuracy (e.g., covariance of estimates) and ambiguity resolution success, across diverse measurement scenarios. Numerical simulations are conducted for common constraint types—including control point initialization, static positioning, and inertial motion—under varying measurement conditions. Results demonstrate that constraints significantly reduce solution errors and ambiguity resolution time in challenging environments, while offering minimal benefit in favorable conditions. The proposed methodology provides a robust foundation for systematic evaluation and optimization of constraint use in GNSS surveying, with practical implications for reducing field time and improving solution reliability.
}
The objective of this study is to investigate the impact of two significant earthquakes, measuring 7.8 Mw and 7.6 Mw, that occurred on February 6, 2023, in Turkey, on the Continuously Operating Reference Stations (CORS) network in Israel. This study analyzed the effect on 16 CORS stations in Israel, with the epicenters of the earthquakes approximately 500 km from the northernmost station and about 900 km from the southernmost station in the network. The seismic events led to both coseismic displacements and postseismic deformations within Israel. The findings revealed significant changes, on the order of a few centimeters, in station locations, both in absolute terms and relative to each other. Stations closer to the earthquake epicenters experienced a more pronounced impact compared to those farther away. The geodetic datum in Israel is defined as a semi-dynamic datum. This datum necessitates periodic updates to account for various factors affecting the movement of the Earth’s crust. Given this context, it is crucial to thoroughly investigate the impact of the February 2023 earthquakes on the CORS network in Israel. This assessment will aid in evaluating changes in site locations, determining their magnitude, and guiding necessary corrective actions to update the Israeli semi-dynamic datum.
}
This study outlines the planning, emphases, and proposed implementation of a gravimetric control network for Israel. The establishment of a comprehensive and accurate gravimetric control network is crucial for various geodetic applications, including geoid determination, gravity field modelling, vertical datum establishment, and geophysical studies. This study aims to provide a framework for the development and implementation of such a network in Israel. The proposed network is divided into two orders. The first order, also known as the absolute order or zero order, comprises four stations situated in geologically stable and tranquil locations. The second order, referred to as the first order, is established through relative gravimetric measurements. This order will encompass 29 stations positioned in areas that are both stable and secure. The zero and first order stations will be evenly distributed throughout the country to ensure homogeneous coverage. The proposed gravimetric network is in conjunction with the requirements to improve the geoid undulation model of Israel. Through the establishment of a small gravimetric network and the implementation of relative gravimetric measurements, we were able to determine the optimal control point density and establish a well-structured methodology for measurement, analysis, and the adjustment process.
}
Estimation of fault-model parameters is a challenge faced by researchers. Traditional statistical tools rely on a velocity field derived from precise coordinates of control-points in GNSS networks, changing over-time. This requires dealing with geodetic datum and deformation-monitoring datum, while handling ill-conditioned state models. This paper describes an algorithm for evaluating full fault-model parameters all at once using a feature-voting technique, while relying on precise GNSS vectors computed with scientific GNSS processing software. The algorithm bypasses the datum issues and deals with numerical instabilities using perturbed data replications. Dealing with gross-errors is an embedded attribute of the technique, and noise is an intrinsic feature needed to cope with the ill-conditioned equation-set problem with respect to the low-frequency nature of the data. Thus, the geodetic datum and deformation monitoring datum becomes irrelevant for this algorithm. Simulations of a locked fault-model, based upon a true solved epoch, derive proper parameter values for a preselected fault-model scenario, including simulations with noise. A case study relies on the northern section of the Dead-Sea fault, on 10 northern sites in Israel's continuously operating permanent stations, based on four true-data epochs of computed vectors in order to evaluate Dead-Sea fault model parameters. Similarity is shown between computed fault-model parameters using the presented feature-voting technique and those estimated by traditional processes; with respect to other researchers' work, at the same area over a similar time period, carried out by a traditional statistical least-squares adjustment procedure, including efforts in gross-error filtering and coping mechanisms with the biases caused from both datum issues. The feature-voting based methodology for analyzing fault-model parameters, using precise GNSS vectors and not precise coordinates; enables simultaneous full fault-model parameter computation while avoiding biases originating in deformation-monitoring datum and other error factors.
}
This paper examines the internal and external reliability criteria of the mixed LS adjustment model. We use the reliability concept to quantify the potential for detecting gross errors and to estimate their impact on the adjusted param-eters. After a short introduction to the mixed adjustment model, the hat matrix and Baarda’s data snooping we describe the theoretical tools developed to define the internal and external reliability in the mixed adjustment model. The paper pre-sents the results of an example of LS adjustment of transformation parameters between two coordinate systems, indicating that the reliability can be used effectively for this model.
}
Indoor navigation based on Pedestrian Dead Reckoning (PDR) is a highly researched topic in recent years. PDR is a two-dimensional dead reckoning technique that employs inertial sensors, such as those available in smartphones, to provide the user's position. If the vertical position component is also required, it can be obtained from the smartphones' barometer. However, unlike accelerometers, approximately, only 10% of the smartphones are equipped with barometers. In this paper, two methods for height difference estimation during stairs motion are proposed. Those are based only on the smartphones' accelerometers and do not require any prior calibration. The proposed approaches are evaluated on different staircases with different smartphone locations on the user. Results show that the proposed approaches yield an average percentage error in the range of 2.5% - 13% when calculating height difference of the examined staircases. Thus, the proposed approach can be implemented alongside traditional PDR approaches to enhance its capabilities to 3D PDR during stairs motion.
}
In the “Internal Reliability” section, an error in composition resulted in the introductory text for Eq. (11b) appearing after Eq. (14), creating an incomplete sentence. The correct introductory text for the equation is as follows: The maximum size of a blunder that could contaminate the ith observation is ASCE regrets the error.
}
This paper examines the reliability criteria in sequential least-squares adjustment. Sequential least-squares techniques are widely implemented to effectively use adjustment processes. We use the reliability concept to quantify the potential for detecting blunders and to estimate their impact on the adjusted parameters. To gain additional insight into sequential least squares, we address internal and external reliability for recursive least squares (RLS) and two-step least squares (TSLS). After a short introduction to RLS, TSLS, and the concept of reliability, the paper describes the theoretical tools we developed to exploit the benefits of reliability criteria in sequential least-squares adjustment. Finally, the paper presents the results of a of two numerical example, indicating that the reliability can also be used effectively in sequential least-squares adjustment.
}
GNSS observations stochastic model influences all subsequent stages of data processing, from the possibility to reach the optimal parameters estimation, to the reliability and quality control of the solution. Nowadays, an uncontrolled use of GNSS stochastic models is common for both data processing and simulation missions, especially in commercial GNSS software packages. As a result, the variance–covariance matrices that are derived in the processing are inadequate and cause incorrect interpretations of the results. A proper method to evaluate the reliability of the stochastic model is needed to reflect the confidence level in statistic testing and simulation mission efforts. In this contribution, a novel method for evaluating the statistical nature of GNSS stochastic model is presented. The method relies on the deterministic nature of the integer ambiguity variable to examine and express the expected multinormal distribution of the double-difference adjustment results. The suggested method was used with a controlled experiment and 24 h of observations data to investigate how the statistical nature of the stochastic model is affected by different baseline lengths. The results indicate that as the baseline length increases, the stochastic model is less predictable and exposed to irregularities in the observation’s precision. Additionally, the reliability of the integer ambiguity resolution success rate (SR) was tested as part of the stochastic model evaluation. The results show a dramatic degradation in the SR prediction level when using an inadequate stochastic model, which suggests using extra caution when handling this parameter unless high-confidence reliable stochastic model is available.
}
Similarity transformation model does not provide a satisfactory solution for non-uniformly deformed systems because it allows only for a uniform scale and right angles. Instead, an affine model can be used, since it characterizes non-uniform dilatations and obliquity of the three axes. The general affine transformation contains 12 parameters. Nonetheless, it is not always necessary to use them all. The question of how many parameters should take part in the transformation and in what combinations is examined in the paper. In order to choose the proper transformation, a refined AIC is proposed. The paper also presents how to conduct the conversion of parameters between different coordinate systems with reference to the invariance property of coordinate transformation. To demonstrate the impact of using variable number of parameters and to observe the influence of coordinate systems on the transformation outcome, we use a network of 18 permanent GNSS stations in Israel as a case study.
}
Tectonic activity and crustal deformation in northern Israel are mainly related to the Dead Sea Fault (DSF) and the Carmel–Gilboa Fault System (CGFS). The CGFS is composed of several NW–SE trending faults while the main faults are the Carmel Fault (CF) and Gilboa Fault (GF). The CGFS divides the Sinai Sub-Plate into two tectonic domains. In this study, we geodetically investigate surface deformation processes in the Carmel Fault region. Beside the processing and analysis of GPS measurements, we highlight geodetic aspects in the process of deformation analysis in geodetic monitoring networks. We implement the Extended Free Network Adjustment Constraints solution to calculate the velocities of 24 sites that were measured eight times between 1999 and 2016 using Global Positioning System (GPS). The regional site velocities were estimated with respect to a local datum that was defined by a stable cluster of sites on one side of the fault. We introduced the site velocities into the estimation of surface deformation parameters by using affine transformation also with respect to a local datum. The coordinates of network sites can be transformed to any desired datum by using extended similarity transformation. Examination of the velocity field in relation to a datum defined by points in the Galilee region raises the suggestion that the velocities in the Yizre’el Valley region are due to activities along the GF or similar trending faults on the northern side of the valley which are halted by the Tivon Hills. The best set of deformation parameters, the one which better describes the velocity field, was determined by the second-order Akaike Information Criterion (AICc). The results show significant sinistral deformations of less than 1 mm/year along the Carmel Fault accompanied with extensions and shear strain.
}
The signal-to-noise ratio (SNR) data are part of the global navigation satellite systems (GNSS) observables. In a marine environment, the oscillation of the SNR data can be used to derive reflector heights. Since the attenuation of the SNR oscillation is related to the roughness of the sea surface, the significant wave height (SWH) of the water surface can be calculated from the analysis of the attenuation. The attenuation depends additionally on the relation between the coherent and the incoherent part of the scattered power. The latter is a function of the correlation length of the surface waves. Since the correlation length changes with respect to the direction of the line of sight relative to the wave direction, the attenuation must show an anisotropic characteristic. In this work, we present a method to derive the wave direction from the anisotropy of the attenuation of the SNR data. The method is investigated based on simulated data, as well by the analysis of experimental data from a GNSS station in the North Sea.
}
The navigation subsystem in most platforms is based on an inertial navigation system (INS). Regardless of the INS grade, its navigation solution drifts in time. To avoid such a drift, the INS is fused with external sensor measurements such as a global navigation satellite system (GNSS). Recent publications showed that the lever-arm, defined as the relative position between the INS and aiding sensor, has a strong influence on navigation accuracy. Most research in this field is focused on INS/GNSS fusion with GNSS position or velocity updates while considering various maneuvers types. In this paper, we propose to employ virtual lever-arm (VLA) measurements to improve the accuracy and time to convergence of the observable INS error-states. In particular, we show that VLA measurements improve performance even in stationary conditions. In situations when maneuvering helps to improve state observability, VLA measurements manage to gain additional improvement in accuracy. These results are supported by simulation and field experiments with a vehicle mounted with a GNSS and an INS.
}
Is coordinate transformation invariant with respect to coordinate systems? Intuitively one assumes so, but the answer is more complex as in some cases it is invariant and in some cases it is not. Invariant coordinate transformation is a transformation where the quadratic form of the weighted residuals (vTPv) is preserved in any coordinate system in which the transformation parameters are calculated. Consequently, invariant coordinate transformation allows converting the transformation parameters that were calculated in one coordinate system to another coordinate system correctly, without the need to calculate the parameters again in the new coordinate system. This paper discusses the invariance property of coordinate transformation and shows the complexity of geodetic coordinate transformations, where some are invariant and others are variant. In variant transformations, the transformation parameters and the quality of the transformation depend on the coordinate system and its definition, an important situation to be aware of.
}
The network of Continuously Operating Reference Stations (CORS) in Israel realized Israel's current geodetic datum and is used to monitor it. It was done by adopting a set of fixed International Terrestrial Reference Frame (ITRF) coordinates for the Israeli CORS stations. This datum serves as the infrastructure for all mapping, surveying, and especially the Cadastre system. The relative motion (3-6 mm/year) along the Dead Sea Fault causes the degradation of the Israeli datum over a relative short time. To manage this problem, the authors examined the use of a kinematic datum. This datum includes a 14-parameter transformation, between ITRF05 to the Israeli plane coordinate system, which is static, in conjunction with a velocity field, all evaluated from global positioning system (GPS) time-series solutions of the CORS in Israel from the past 10 years. The results of this examination are promising and show that with a kinematic datum, the accuracy can be maintained over a long period of time.
}
We present, in this paper, a new methodology for spectral unmixing, where a vector of fractions, corresponding to a set of endmembers (EMs), is estimated for each pixel in the image. The process first provides an initial estimate of the fraction vector, followed by an iterative procedure that converges to an optimal solution. Specifically, projected gradient descent (PGD) optimization is applied to (a variant of) the spectral angle mapper objective function, so as to significantly reduce the estimation error due to amplitude (i.e., magnitude) variations in EM spectra, caused by the illumination change effect. To improve the computational efficiency of our method over a commonly used gradient descent technique, we have analytically derived the objective function's gradient and the optimal step size (used in each iteration). To gain further improvement, we have implemented our unmixing module via code vectorization, where the entire process is 'folded' into a single loop, and the fractions for all of the pixels are solved simultaneously. We call this new parallel scheme vectorized code PGD unmixing (VPGDU). VPGDU has the advantage of solving (simultaneously) an independent optimization problem per image pixel, exactly as other pixelwise algorithms, but significantly faster. Its performance was compared with the commonly used fully constrained least squares unmixing (FCLSU), the generalized bilinear model (GBM) method for hyperspectral unmixng, and the fast state-of-the-art methods, sparse unmixing by variable splitting and augmented Lagrangian (SUnSAL) and collaborative SUnSAL (CLSUnSAL) based on the alternating direction method of multipliers. Considering all of the prospective EMs of a scene at each pixel (i.e., without a priori knowledge which/how many EMs are actually present in a given pixel), we demonstrate that the accuracy due to VPGDU is considerably higher than that obtained by FCLSU, GBM, SUnSAL, and CLSUnSAL under varying illumination, and is, otherwise, comparable with respect to these methods. However, while our method is significantly faster than FCLSU and GBM, it is slower than SUnSAL and CLSUnSAL by roughly an order of magnitude.
}
The geoid is the equipotential surface that coincides with the sea level in the absence of such dynamic effects as tides, wind, ocean currents, and other disturbing forces. On land, geoid models are determined by using precise leveling, Global Navigation Satellite System (GNSS) measurements, and gravimetry measurements. However, in coastal areas, where performing precise leveling is not possible, geoid modeling relies solely on gravity measurements. Spaceborne gravimetry missions provide gravimetric measurements with global coverage. These measurements have low spatial resolution, which can reach distances of tens and hundreds of kilometers between tracks. Airborne and shipborne gravity measurements can be used to fill the gaps between tracks. In the absence of airborne and shipborne gravity measurements to densify the measuring data, shipborne GNSS measurements may provide a low-cost method for overcoming this problem in coastal areas. After applying several corrections to the raw GNSS measurements (accounting for systematic effects induced by ship dynamics and other static and dynamic impacts from tides, atmospheric pressure, or wind stress), approximate geoid height with fair accuracy could be extracted. An experiment was conducted along the Israeli coast, during which several GNSS surveys were carried out between the years 2011 and 2015. This paper illustrates the steps needed for the extraction of such heights and provides a comparison of the results between the Israeli official geoid model and the expanded one, complete with its quality assessment.
}
Many methods and techniques have been developed to detect gross errors in geodetic measurements, but none seems to have prevailed. Statistical tests and robust methods are the most common approaches for detecting outliers in geodetic measurements. Least-squares adjustment and iterative attitudes are the essence of those methods. In this paper, closing loops in Global Navigation Satellite System (GNSS) networks are used to detect gross errors. Spanning trees are used to define a set of independent loops in the network. Careful examination of the misclosure of loops assists in defining the faulty vectors. The method is very effective and delivers another alternative for outlier detection without using adjustment computation and statistical tests. The method of outlier detection by means of spanning trees is presented and tested against well-known methods like convectional statistical tests (w-test, τ -test, and τ-test) and robust M-estimation methods (Andrews, Huber, and Danish). A number of tests were performed on a GNSS network that contains 115 points and 917 vectors to detect gross errors in different scenarios, and the results are presented in the paper. Based on the results of the presented tests, it is seen that the w-test and the M-estimation methods correctly detect all outliers in the GNSS network, whereas τ-tests and t-tests do not always detect the correct errors. The new method for detection of gross errors by means of spanning trees performs quite well and can correctly exclude all outliers with only one iteration.
}
Two-step analysis of deformation network enables the extraction of geodynamical quantities from geodetic measurements campaigns in two steps. In the first step the measurements’ mathematical model is realized for each monitoring campaign and in the second step the deformation model is examined. The mathematical model is usually conceived as being absolutely correct, while the validity of the deformation model and its system noise is frequently limited. The deformation model is commonly presented by kinematic model although dynamic model might describes the geophysical reality more accurately. Dynamic model is usually characterized by nonlinearity, which makes difficult the analysis of deformations in relative to a stable datum. Therefore, many of the control networks that are used for deformation monitoring and are measured by geodetic measurements are currently defined by kinematic models. In monitoring networks, global effects can impair the data processing and the deformation analysis and cause the deviation of the network solution. Extended free net adjustment constraints is a mathematical method that effectively coping with global effects. An extended solution of geodetic network for deformation monitoring includes the solution of extended parameters, in addition to those received in a standard solution. Such a solution enables to sterilize the geodetic measurements from their datum definition content in the first step, and extract the deterministic movement in the second step. The paper shows the great potential of using combination of the extended free net adjustment constrains and the two-step analysis of deformation networks.
}
In-land geoid models rely on several measuring techniques. The quality of those models is directly related to the spatial resolution of the measurement data. Occasionally, a local geoid model does not cover the coastal area at all and a local marine geoid simply does not exist. ShipborneGNSS measurementsmay provide away of overcoming this problem in coastal areas. However, several corrections to the raw measurements must be applied in order to account for systematic effects induced by ship dynamics and other static and dynamic impacts from tides, atmospheric pressure or wind stress. This paper presents the theoretical background for the method and the results of a case study in the estuary of the Weser River in Germany. A series of GNSS measurements were carried out aboard a ship and the approximate geoid height along the river was derived. For accuracy assessments of this method, the resultswere compared to the German Combined QuasiGeoid 2011 (GCG2011). The results are very promising and indicate the ability to extract geoid heights from shipborne GNSS measurements.
}
Many ship-borne geodetic surveys at sea, such as Global Navigation Satellite System (GNSS)-based sea surface height (SSH) observation, acoustic profiling of the bottom, and others, deal with a dynamic topography which undergoes several changes during the survey campaign (e.g., changes in tide, salinity and currents). Those changes affect the measurements and may causes for some variations in the results. There are several methods for tidal variations correction, being the most dominant phenomena, such as tidal zoning, tidal constituent interpolation or ocean tidal models. In this study, we have implemented the tidal constituent interpolation method for the Israeli coastline in order to assess its quality and determine whether it is suitable for use in this particular region. This paper depicts the interpolation method, discusses some difficulties in the implementation for the Israeli coast and presents results from exemplary processing. In addition, we compare the results to those obtained using global and regional tidal models.
}
Relative GPS positioning based on VRS data makes it possible to reduce the observation time span needed for accurate positioning in long range distances from the reference station. The ability to derive an efficient and precise baseline solution with VRS data depends on the level of precision of the ionospheric assumption in the virtual observations. Increasing the ability to produce efficient VRS coverage will necessitate the formulation of a trustworthy technique for mapping the ionospheric delay at larger distances (hundreds of kilometres). In order to derive the minimal conditions needed for such a mapping technique, this study aims to explore how the accuracy of a VRS is impacted by the ionosphere, when it is produced at long range distances from the reference stations using different interpolation methods. Over the course of this research, several experiments that examined the precision of setting up the VRS in different scenarios were conducted, in order to determine the optimal method for mapping the ionosphere with the objective of providing long-range VRS service. The KRIGING method was found to be the most appropriate among the tested methods for mapping the ionosphere in the process of creating VRS observations. The ionospheric model that was created on the basis of KRIGING described the ionospheric delay's temporal behaviour closest to the real variability as a function of time.
}
A study of deformations, which is based on the use of geodetic measurements, is usually performed by defining a kinematic model. Such a model, when used to describe a complex geophysical environment, can lead to a partial estimation of the deterministic dynamics, which characterize the entire network. Usually, in a case of deterministic nonlinear movements in the network, there is no possibility to determine a stable datum that may serve as a basis for deformation analysis. Today, the concept of stability in time ascribes rigidity to a congruent datum. This paper redefines the concept of the datum congruency and presents the development of a new dynamic datum, which more closely represents geophysical reality. The new datum changes the main characteristics of a traditional datum and successfully overcomes some of its inherent disadvantages. As an example, the proposed algorithm of the dynamic datum is applied to obtain a deformation analysis in the Carmel fault environs, one of the major geological structures in northern Israel.
}
The Carmel fault is one of the major geological structures in northern Israel. The fault is characterized by potentially hazardous seismic activity. It runs across densely populated areas and in proximity to the Haifa Bay petrochemical factories. Geological and geophysical studies have implied both horizontal and vertical movements along the Carmel Fault. Geodetic study - based on precise leveling that has been measured three times in 1987, 1992 and 2003, using the standard free net adjustment solution - presented significant vertical deformation. Precise leveling measurements, as other geodetic measurements, partially define the network's datum. The standard free net adjustment solution treats these elements as global geometric parameters of the network, which are defined with a stable datum over time. However, this assumption is not necessarily consistent with reality, and datum elements usually change over time. This makes it necessary to improve the solution, using an extended free net adjustment constraints analysis. The current paper presents an improved analysis of the same precise leveling measurements, which enables the cleaning of the leveling measurements from their datum content. This cleaning minimizes the effect of datum elements on the revaluated deformation and produces results that more clearly reflect the geophysical reality.
}
The Carmel Fault is one of the major geological structures of northern Israel. It is the northwestern part of Carmel-Tirtza Fault System and a northwestern branch of the Dead Sea Fault. The Carmel Fault region is covered by a monitoring geodetic network consisting of 23 sites, which were measured four times between 1999 and 2010 by means of GPS. The site velocities can be estimated only if the datum of the network has not been changed between measurement epochs. The GPS vectors must be adjusted so that the datum will remain undisturbed throughout the measurement campaigns. Usually we assume that GPS vectors define the network datum components of orientation and scale. Fluctuations in the GPS orbits could affect the orientation and scale between monitoring campaigns and therefore, in this study, we assume that GPS vectors are not immune to changes in their datum content. An appropriate approach is takento prevent the inclusion of these components in the adjustment of a 4D network. If not, the result will be an inevitable mixture between the deformation parameters and the datum components of the GPS vectors. In this study the GPS vectors from each campaign are stripped from their datum content using the extended free network adjustment constraints. The datumless measurements are used to define the datum by preliminary coordinates and linear constraints, which remain constant for all monitoring campaigns, as well as to define the position of the network points and their velocities. Later on, the variations across the network geometry can be modeled by means of a physical model.
}
In geodetic monitoring networks, the deformation parameters can be estimated only if the datum of the network has not been changed between measurement epochs. The measurements of a monitoring network must be adjusted so that the datum remains undisturbed. In deformation analysis, similarity transformation is used intensively in order to bring all monitoring campaigns to the same common datum. However, there are geodetic measurements which contain datum definition components. When part of the datum definition contained in the measurements is not constant in time, the estimated deformation parameters could be erroneous. An appropriate approach should be taken to prevent the inclusion of these components in the adjustment of a 4D network. If not, the result is an inevitable mixture between the deformation parameters and the datum components of the measurements. The extended S-transformation allows us to strip the datum content from a set of coordinates that contain the complete contribution of the geodetic measurements to a datumless set of coordinates. Based on the datumless sets of coordinates, the variations in the network geometry can be modelled by means of a physical model without the influence of a datum definition inherent in geodetic measurements. Following a short introduction of the concept of extended free net adjustment constraints, the development of an extended Stransformation is presented. Two examples of a trilateration network and a GPS network are presented for implementing the method.
}
Extraction of the deterministic ingredient of a dynamic geodetic control network: A minimum constraints solution, which resolves the datum defect of a control network, is an arbitrary solution that may result in a systematic error in the estimation of the deformation parameters. This error is not derived from measurements and is usually inconsistent with the geophysical reality. A free network is affected only by errors of measurement and, therefore, a free network is an accepted way of coping with this problem. Study of deformations, which is based on the use of geodetic measurements, is usually performed today by defining a kinematic model. Such a model, when used to describe a complex geophysical environment, can lead to the partial estimation of the deterministic dynamics, which characterize the entire network. These dynamics are themselves expressed in measurements, as the adjustment systems' residuals. The current paper presents an extension of the definition of the parameters that are revalued. This extension enables the cleaning of measurements by means of the extraction of datum elements that have been defined by geodetic measurement. This cleaning minimizes the effects of these elements on the revaluated deformation. The proposed algorithm may be applied to achieve the simultaneous estimation of the physical parameters that define the geophysical activity in the network.
}
The existing knowledge about the recent crustal deformations along the Carmel Fault in Northern Israel which passes the city of Haifa is to a certain degree ambiguous. Depending on geological, geophysical or geodetic sources the movement rates and senses range from 1. mm/yr sinistral up to 4. mm/yr dextral. In this paper we analyze GPS data from a regional network observed between 1999 and 2009 and derive global and regional velocities for 23 sites along the fault. The regional site velocities were estimated with respect to a local datum that was defined by a stable cluster of sites on one side of the fault and the horizontal velocity field shows deformations of up to 4.5. mm/yr dextral. In combination with an S-transformation the site velocities were used to estimate the parameters of a dislocation model based on elastic half space theory. We compare the results with expectations from slip rate analysis of seismicity parameters. In addition the resulting fault slip field is used to derive a fault-related velocity field.
}
A novel unmixing methodology is presented, searching for a fraction combination of end-members (EMs) that reconstructs the integrated source signal. The search starts with computing an initially estimated unmixing solution and then assesses combinations selected at random within an envelope surrounding this estimated solution. From each of these combinations, it then progresses iteratively along a path of neighboring combinations, so as to minimize the spectral angle between the corresponding (integrated) signatures and the source signal, until reaching a satisfactory solution. The new iterative fraction combination search (IFCS) was compared to the standard least squares unmixing (LSU). An assessment of both methods was conducted with a real Airborne Visible/Infrared Imaging Spectrometer image and nine synthetic images generated by randomly selecting fractions for two up to ten EMs derived from this real image. Considering all these EMs for the unmixing solution (not knowing specifically which or how many of them are actually mixed at each pixel), the IFCS method performed considerably better than LSU.
}
In 2005, Israel implemented a new geodetic datum, IGD05-Israel Geodetic Datum 2005. The new datum was defined based on a network of 13 permanent Global Navigation Satellite Systems (GNSS) stations. The network provides a reference frame for precise GNSS measurements and serves as the major geodetic control network in Israel. Due to the dynamic nature of the Earth crust, the relative positions of the permanent GNSS stations are not fixed but are time dependent. The set of coordinates that were valid in 2005 no longer represent the current position of the points, and a datum update was required. The method for determining the need for a datum update using statistical tests, as well as the actual update campaign, are presented and discussed in this paper. In addition, the impact of a datum update to Israel's plane coordinates system is demonstrated.
}
Deformation parameters are estimated based on a time series of monitoring campaigns. For each monitoring campaign, the measurements' contribution is in determining the relative positions of the network points and defining the datum of the network. When part of the datum definition contained in the measurements is not constant in time, the estimated deformation parameters could be erroneous. Measured distance, for example, can be assumed to have scale. But fluctuations in the instrument oscillator, when using the same instrument for all campaigns or when using a different instrument in each campaign, could affect the scale between monitoring epochs. For a single monitoring campaign, datum parameters contained in the distance measurements may be used for estimating the coordinates of the network points. However, in four-dimensional (4D) geodetic networks, a part of the datum definition determined by the geodetic measurements may not remain consistent. For example, the estimated deformation parameters related to scale could be wrong in distance-based networks. In this study, the measurements from each campaign are stripped from their datum content by extended free network adjustment constraints. The datumless measurements are used to define the datum by preliminary coordinates and linear constraints that remain constant for all monitoring campaigns, as well as to define the position of the network points. Subsequently, the variations in the network geometry can be modeled by means of a physical model. Following an introduction of the concept of extended free network adjustment constraints and a development of theoretical tools, the paper presents the deformation analysis of a small electronic distance measurement (EDM) network measured six times between 1989 and 2008 using the proposed method.
}
The sensitivity of a geodetic monitoring network is defined as its capacity to detect and measure movements and deformations in the area covered by the network. This paper attempts to study the effects of datum definition on the sensitivity of geodetic networks. Principles from continuum mechanics are used to analyze the datum definitions required for a sensitive network, and it is shown how the sensitivity of a monitoring network is strongly influenced by the geometry of the network points. This paper presents a new perspective and describes relevant parameters that enable defining and quantifying the influence of the datum on the sensitivity of geodetic networks. Following an introduction of the concept of geodetic networks sensitivity and a development of theoretical tools, the paper presents the sensitivity analysis of a group of points in the network and the influence of datum definition on the sensitivity of geodetic monitoring networks.Two main conclusions arise in the paper, the sensitivity is i variant to the datum definition and the geometric location of the network points is extremely important to the network sensitivity, as different point distributions lead to different levels of sensitivity.
}
We study the surface displacement close to the Dead Sea Fault (DSF) system in the Jordan Gorge area, northern Israel, using 18 years of Electronic Distance Measurement (EDM) from the Kfar Hanassi network. We focus on the near-fault velocity pattern and address the question of whether shallow creep is observed in this part of the fault. The near-fault, dense geodetic network of Kfar Hanassi was established across the Dead Sea Fault, where displacements of several millimeters per year between the Sinai sub-plate and the Arabian plate are expected. The results of five campaigns carried out between 1990 and 2008 are presented. Four campaigns consisted of annual measurement between 1990 and 1993 using a Mekometer ME5000. An additional campaign was carried out in the summer of 2008 using a Leica TC2002. The large time interval between the campaigns contributed dramatically to the ability of the Kfar Hanassi network to detect movements. The distance measurements were analyzed by a Two-Step analysis. In the first step, the distance measurements were processed sequentially without modeling the variations in the plane position of the network benchmarks. In the second step, the variations in the network geometry were modeled by means of a physical model. In this study a linear model of movements was tested to describe the plane position of the network benchmarks. The results indicate a left-lateral and extension motion along the DSF with a rate of a few tenths of a millimeter per year close to the fault. The calculated velocity field is in agreement with a fully locked fault model. Using a locked fault model and assuming a slip rate of 5 ±1.5 mm/year of movement between the Sinai sub-plate and the Arabia plate, as observed in previous geodetic studies, the modeled locking depth in this segment was found to be 8.1±2.5 km. This result is in agreement with previous studies using far-field GPS measurements.
}
Since the beginning of 2006 the vertical control system in Israel has been ellipsoidal. The Survey of Israel constructs and maintains the ellipsoidal vertical control system based on permanent Global Navigation Satellite System (GNSS) stations. Nowadays, the vertical control system's objective of providing a framework upon which topographers and engineers can base and adjust their heights is achieved more easily by GNSS measurements. Despite this, the vertical orthometric control system is still in use since many height data users prefer the orthometric system. However, the characteristics of the orthometric control system are localized.The Geoid Undulation Model is one of the foundations of the geodetic infrastructure. It is used to connect ellipsoidal and orthometric heights. Intensive utilization of GNSS for geodetic, surveying and engineering applications necessitates the rapid development of an undulation model. Today, the efforts to develop a geoid undulation model with an accuracy level of one centimetre over an entire country demand multiple resources. This paper suggests a method for developing an orthometric control system with a reasonable accuracy level on a nationwide basis by means of GNSS measurements, ellipsoidal vertical control and an official geoid undulation model. The best available geoid undulation model can be used as the official geoid undulation model, regardless of its accuracy level.Research was conducted in Israel in order to test the feasibility of the idea of using an official geoid undulation model. Two kinds of official models were tested, the world wide geopotential model GPM98B and a local countrywide model computed by the Survey of Israel. We compared the orthometric height differences obtained by GPS measurements using the undulation model with the known orthometric differences. This paper presents the results of these experiments. It verifies the capability of the suggested technique to define seamless orthometric vertical control, adequate for most geodetic and surveying purposes, via a low-cost and fast procedure.
}
The geodetic-geodynamic network of Israel, named G1, was constructed in the 1990s, with the aim of understanding recent tectonics and deformation in Israel. The network contains approximately 150 points which were built according to high-standard technical specifications to ensure their high geotechnical stability. In this research we use measurements of 60 points, from the northern part of the G1 network together with five permanent GPS stations to monitor current crustal movements across the Dead Sea Rift (DSR) in the north of Israel. The DSR is the northern part of the Syrian-African Fault. It extends from southern Turkey to the Aqaba Gulf and separates the Arabian plate from the Sinai sub-plate. Recent researches show that the DSR behaves as a locked strike-slip fault The research makes use of the Two-Step analysis of dynamical networks. This method is based on a first step of independent adjustment of every measurement campaign to a set of network points coordinates, followed by a second step in which we use the coordinates as pseudo-observations for adjusting a set of kinematical or dynamic parameters. The least squares estimation of the second step assumes an ideal mathematical model of the tectonics. While the correlation between the mathematical model and the physical phenomenon is not absolute, the solution is biased due to the correlation. That is the main reason for using prior information for matching of the model to the phenomenon We use the locked fault model to describe the dynamic behavior of points in the north of Israel. It relies on an arctangent function and depends on four independent parameters. The locked fault model suffers from an instability relationship between its parameters since it deals with extremely different scales of its parameters By using prior knowledge we evaluate the model parameters by enforcing constraints on the adjusted parameters. A second solution of the model parameters is presented by extended free dynamic network. In this method we adjust the kinematical parameters simultaneously with the dynamical softened parameters. A third solution is achieved by regulation of the normal matrix in certain ways The paper presents results which based on two GPS measurement campaigns carried out in 1996 and 2002. Applying different solutions strengthens the possibility of correct use of the mathematical model to achieve results in close proximity to the actual physical behavior and enables reaching a reliable solution. The solution indicates a left lateral motion of the DSR in a rate of 2-7 mm/yr. In addition, the system is characterized by a high level of model noise which indicates an unsuitability of the mathematical model to the geophysical reality.
}
Since the beginning of 2006, the vertical control system in Israel has been ellipsoidal. The Survey of Israel (SOI) will not continue with nationwide precise leveling. Instead, data from permanent Global Navigation Satellite Systems (GNSS) stations are used to develop and maintain Israel's ellipsoidal vertical control system. Currently, the objective is to provide a framework on which topographers and engineers can base and adjust their heights, and this is achieved more easily by GNSS measurements. Despite this, many users of height data prefer the orthometric system, even though its control is localized. A geoid undulation model is one of the foundations of the geodetic infrastructure. It is used to connect ellipsoidal and orthometric heights. Intensive utilization of GNSS for geodetic, surveying and engineering applications necessitates the development of an undulation model. Efforts to develop such a model with an accuracy level of 1 centimeter over an entire country demand multiple resources. This paper suggests a method for developing a national, orthometric control system with a reasonable accuracy, using GNSS measurements, ellipsoidal vertical control, and an official geoid undulation model. Research was conducted in Israel in order to test the feasibility of using an official geoid undulation model. Two kinds of official models were tested: the worldwide geopotential model (GPM98B) and a local, countrywide model computed by the Survey of Israel. We compared orthometric height differences obtained by GPS measurements with the known orthometric differences. This paper presents the results of those experiments. The technique proposed in this paper was found to define seamless orthometric vertical control adequate for most geodetic and surveying purposes, at low cost and fast. Of special interest in the paper is the comparison between the proposed idea and the National Geodetic Survey (NGS) attitude toward GPS-derived orthometric heights. The advantage of using the official geoid undulation model for the acquisition of orthometric heights is demonstrated.
}
This paper presents an inexpensive, efficient, low-weight airbornern system based on two non-metric cameras together with a GNSS receiver and its antenna, The main camera is oriented towards the ground, and the other, being a solar camera, is oriented towards the sun and used instead of an IMU system to determine the system's tilt angles. The device can be carried by small helicopter, any tiny air carrier, or even an unmanned small aircraft. The system is suitable for large scale photogrammetric mapping of small tracts of difficult terrain of special interest, and allows the recording of small but significant land deformations which occur within a short time span. The photogrammetric measurements are done without any ground control: the images' exterior orientations are determined by the coordinates of the GPS antenna's position at the moment of exposure as well as by the sun's geocentric position and by the location of its image in the solar photo. This paper describes the calibration of such a system.
}
The GPS antenna is the connecting component between the GPS satellite and the GPS receiver. Its function is to transfer the satellite signal propagation to the receiver with minimum interruption. A satisfactory process is expected to result in an accurate and reliable performance of the GPS receiver. A multipath error is the dominant error source connected with GPS positioning. Mitigation of such errors can be achieved by better signal processing and antenna design. This paper attempts to examine the effects of the pseudo-range multipath in a variety of GPS antenna types and compare the ability of different antenna types with regards to the multipath. When the geometry between the GPS satellite and the receiver remains unchanged, a comparison study between antenna types is possible since the pseudo-range multipath pattern is repeated every sidereal day. The multipath comparison was carried out for three types of pseudo-range, the C/A code and the P-code modulated on the L1 and L2 carrier phase. The multipath pseudo-range from several satellites with different elevation angles was used in the assessment of the multipath effects. The method of comparison and the test description are also presented. Five types of GPS antennas were examined in this study. Differences in the capability of the antennas to reduce the pseudo-range multipath were detected. It is shown that a well designed antenna will assist in the mitigation of the multipath, and some geodetic antennas are less suitable for this purpose. It is also shown that ground planes play a major role in the multipath mitigation.
}
This paper attempts to assess the use of Global Navigation Satellite System (GNSS) as an accurate, reliable, and easy tool for sea level measurement. The GNSS technique was incorporated into a float based tide gauge system. A prototype of such an instrument was developed based on principles of conventional tide gauges, where high frequency noise is reduced mechanically. The ability of the GNSS based tide gauge (GTG) to monitor sea levels was tested in several experiments. The performance of the GTG was compared to that of a traditional tide gauge. The method of data analysis and data comparison between the GPS measurements and the tide gauge data is presented. The results show that the GTG is equal in performance to the traditional float operated tide gauge. It seems that the GTG is capable of delivering the same level of accuracy (1 cm), and its results are as reliable as its competitor, the traditional float tide gauge. The suggested instrument can be easily integrated into the array of permanent GNSS stations and assist in absolute measurements of sea level changes, caused by global warming and the greenhouse effect, for example.
}
The classical geodesist' dream of a dense, accurate, reliable and homogeneous countrywide levelling control network is a luxury even for the richest countries and will probably remain a dream. Prior to the GPS era there was no alternative to precise levelling. Now there is. The authors suggest a new approach to orthometric height control in which the best available geoid model is used as official, statutory model from which to deduce countrywide orthometric heights, while ellipsoidal heights are measured with GNSS. Developing countries may benefit.
}
Rapid population growth in the 21st century is a major contributor to the shortage of usable land. As this shortage increases, it drives the cost of land higher and presents a challenge for land management in countries around the world, especially small countries. The rising prices of land resources causes a demand for better, more homogeneous and more accurate marking and reinstating of land parcel boundaries. Current cadastre systems are unable to fulfill this requirement. The move to a Legal Digital Cadastre (LDC) system, in which the coordinates of the boundary points serve as a legal record, is a possible solution. Incorporating GPS measurements that are based on permanent GPS stations is a plausible solution when aiming for the required homogeneity and accuracy levels. However, the use of permanent GPS stations, which are based on a dynamic coordinates system, could cause changes in a boundary point coordinates over time. Moreover, tectonic movements and deformations in the earth crust cause shifts in boundary points and their coordinates. The expected change in the coordinates of boundary points thus requires a transition to a dynamic cadastre system. This paper presents a simulation of a reinstatement of boundary points and discusses the need for a dynamic cadastre system. The requirements and possible difficulties of establishing such a system are discussed and a possible structure for such a future LDC system is presented.
}
Cadastre is a method for registration of land ownership. Due to the major legal importance of marking parcel boundary points in the field, constant re-measuring, reinstating and marking of boundary points are required. In Israel this process is characterized by a predominant and continuous difficulty in the consistent renewal of boundary points due to the different measurement descriptions in the field notebooks, as well as the inhomogeneous measurements. This difficulty is increased due to the use of the "old" horizontal control network as the basis for the measurements, especially as the "old" network is inhomogeneous and is characterized by low accuracy. As the Survey of Israel (SOI) is preparing for a transfer into the age of analytical cadastre and is setting new measuring standards, and following the incorporation of the new Israeli ITM control network in 1995, this paper will attempt to suggest a new process of reinstating and marking parcel boundary points based on Real Time Kinematic GPS technology and using specially characterized "preferred points". The research was carried in two different areas in the north of Israel and examined six methods, comparing them to current methods employed by surveyors. The results point to the immense potential of the measurement methods based on RTK GPS technology and the solving of the measurements in a local network. The results also indicate that measurement methods that incorporate "preferred points" that existed in the field at the time of the original survey and still do, hold an increased potential for cadastral mapping. By using the proposed RTK GPS based methods and incorporating a local network solution, boundary points can be measured with an accuracy level of 10 cm at a 95% confidence level and with smaller standard deviation rates.
}
Studies of forest biomass dynamics typically use long-term forest inventory data, available in only a few places around the world. We present a method that uses photogrammetric measurements from aerial photographs as an alternative to time-series field measurements. We used photogrammetric methods to measure tree height and crown diameter, using four aerial photographs of Yatir Forest, a semi-arid forest in southern Israel, taken between 1978 and 2003. Height and crown-diameter measurements were transformed to biomass using an allometric equation generated from 28 harvested Aleppo pine (Pinus halepensis Mill.) trees. Mean tree biomass increased from 6.37 kg in 1978 to 97.01 kg in 2003. Mean plot biomass in 2003 was 2.48 kg/m2 and aboveground primary productivity over the study period ranged between 0.14 and 0.21 kg/m2 per year. There was systematic overestimation of tree height and systematic underestimation of crown diameter, which was corrected for at all time points between 1978 and 2003. The estimated biomass was significantly related to field-measured biomass, with an R2 value of 0.78. This method may serve as an alternative to field sampling for studies of forest biomass dynamics, assuming that there is sufficient spatial and temporal coverage of the investigated area using high-quality aerial photography, and that the tree tops are distinguishable in the photographs.
}
This paper attempts to study the effects of datum definition on the reliabilty of geodetic networks. Particular attention is paid to the geometry of datum points, defined here as the number and distribution of the datum points, and to its effect on the external reliability of the network points. While the internal reliability of a network is independ ent of datum definition, the external reliability depends heavily on the distribution of datum points. This paper presents a new perspective and describes relevant parameters that enable to define and quantify the influence of the datum on the external reliability of geodetic networks. Following an introduction of the concept of geodetic networks' reliability and a development of theoretical tools, the paper presents results of numerical experiments carried out with a schematic horizontal GPS network. These results indicate that the reliability of the adjusted coordinates in a geodetic network depends on the geometrical distribution of the points that define the datum of the network.
}
The geology of Israel is dominated by the Dead Sea Rift separating the Arabian plate from the African plate. Its influence on the geological structure in Northern Israel is strongly evident in the secondary faulting running in a general northwesterly direction. Northern Israel is enriched with seismological activity which causes significant horizontal and vertical deformations. In Israel there is an infrastructure of 16 permanent GPS stations scattered around the country. This infrastructure enables sequential monitoring of main faults, but its relatively low density does not enable monitoring of secondary faults. During the beginning of the Nineties the geodetic-geodynamic network in Israel was designed and constructed by the Survey of Israel and the Geological Survey of Israel. It contains about 160 points that homogeneously cover the state of Israel, when about third of them are located in Northern Israel. The location of the points was designed mainly according to geological considerations so that it would have the potential of monitoring deformations in primary and secondary known faults over Israel. The network was measured twice in 1996 and in 2002. The data analysis enables the study of movements in northern Israel with high resolution. The GPS campaigns were planned and carried out in a way that ensures high precision and reliability. Each campaign was processed using scientific software. In order to obtain the velocity field of the network points in Northern Israel, the monitoring analysis was carried out by the two-step analysis method of dynamical networks. The analysis enables, for the first time, to map in detail the active faults in the region.
}
The Geodetic-Geodynamic network (G1) was established with the intention of monitoring recent crustal deformations in Israel and serving as a major control network. In 1996 the network was measured for the first time using GPS. The goal of the proposed design is to improve the ability of the network to detect and measure movements and deformations, based on the geological phenomena to be monitored, while satisfying the demand for high accuracy and reliability. This paper presents the network configuration design of the second GPS measurement campaign of the G1 network held during 2002. Sensitivity analysis of the network, as dependent upon a postulated velocity field, was used as the basis for the network configuration design.
}
In theory, using a GPS system in conjunction with an Inertial Measurement Unit (IMU) enables photogrammetric mapping even without using ground control points. But such systems are expensive, not highly accessible, and not suited for close range photogrammetric measurements based on airborne video photography. This paper presents an alternative modified system which enables setting the position and attitude of video images acquired from a helicopter. It is a fairly simple system comprised of an analogical video camera and two kinematic GPS rover receivers. One GPS antenna is located close to the camera and used to locate the camera at the time of the image acquisition. The second antenna is suspended underneath the helicopter. It functions as a flown control point and appears in all the video images. Thus, a photogrammetric model or strip is created in which the coordinates of the exposure point and of one of its image points are always known in all the photographs. The solution process for such a photogrammetric model or strip is presented, as well as, the results and accuracy of the experiments that were carried out to test the system.
}
Mount Carmel fault is one of the major geological structures in northern Israel, characterized by intense, continuous, and potentially hazardous seismic activity. A small monitoring network, spanning an area of 40 by 30 km. and consisting of 17 points, was constructed. Four sets of GPS measurements were taken between 1990 and 1999 as well as two campaigns of precise levelling. Two-Step analysis of the GPS measurements was carried out to quantify recent vertical tectonic deformations. Strict analysis of the GPS and the levelling data shows significant vertical movements in the area. Two independent methods are pointing to the same vertical behavior at the monitored region, indicating that the Carmel range uplifts at a rate of 5 mm per year relative to its surroundings.
}
The ultimate goal of the Survey of Israel (SOI) is to be capable of restoring and defining cadastral boundaries in Israel with an accuracy of 5 cm, at a 95 percent confidence level. In order to achieve this goal, we should be able to measure accurate and reliable horizontal control points and define their rectangular coordinates. Measuring new control points at this accuracy in a homogeneous network can be done by using GPS techniques underpinned by reliable, permanent GPS reference stations. However, integrating measurements performed during the last decade in classical networks (which were characterized by lower accuracy levels) with measurements based on permanent GPS reference stations poses a problem. The Israeli Geodetic Control Network will be based on an array of permanent GPS reference stations. A new datum, called ILGD05 (Israeli Geodetic Datum 2005), was defined for these stations. The transformation of geographic coordinates in ILGD05 to an improved national grid was adopted in a manner that would minimize changes in the existing rectangular coordinates values. This paper describes how the Survey of Israel met the demands and capabilities of the innovative technology. Following a more detailed description of the problems, we discuss the options for improving geodetic control, as well as the reasons for the decisions that were made. The paper suggests a strategy for the implementation of the proposed change in Israel, which will lead us into a new era in geodesy and surveying.
}
The Carmel fault is one of the major geological structures in northern Israel, characterized by intense, continuous, and potentially hazardous seismic activity. Recent studies have implied both horizontal and vertical movement along the Carmel fault. This study presents the results of three measurement campaigns of a leveling line across the Carmel Mountain through the Carmel fault towards Tiv'on Hills and the Lower Galilee, in the period 1987-2003. Two models are used to analyze the observed deformation: a linear model and a quadratic model. Our results show significant uplift of the Carmel Mountain range between 1987 and 1992, and moderate subsidence between 1992 and 2003. The acceleration along the leveling line is also given. Our results also show high vertical deformation in the western slopes of the Carmel Mountain, in contradiction to the low seismicity of this area. These results must be confirmed by additional periodic leveling surveys and other geodetic results.
}
This paper reconsiders the two-step analysis method in an attempt to show how correct processing of both steps will ensure results identical to those obtained when using the one-step method and moreover may result in improved variance-covariance estimation of the deformation parameters. The approach for solving a vector of parameters indirectly from the measurement vector by using a vector of pseudomeasurements is referred to as a two-step analysis. In deformation networks, the first step is processing the geodetic measurements sequentially without modeling the variation in the network geometry. The results of this first step are sets of network point coordinates pertaining to the specific epochs of the measurements. In the second step the variation in network geometry is modeled. The result of this step is a set of deformation model parameters. It is argued that a proper processing of the two-step method will ensure a correct estimation of the variance-covariance matrix of the deformation parameters; which is a critical value in the overall deformation analysis scheme.
}
Repeated precise leveling surveys carried out during the past decade point to an instability of the nodal points in the leveling network in the southwest part of Israel. This situation prevents the adjustment of the leveling network to ensure correct heights for benchmarks. Modeling the regional and local vertical movements of points will enable adjustment of the leveling network, which contains lines that were measured in different times. Nine GPS campaigns were carried in the region over a period of one calendar year to monitor the stability of the network's nodal points. The large number of monitoring sessions enabled the investigation of the fluctuations of the nodal points, based on physical processes such as the cyclic effects of swelling and shrinking of the ground. The GPS measurements were analyzed by a two-step analysis. In the first step, geodetic measurements were processed sequentially without modeling variations in the height of the network's points. In the second step, the variations in the network geometry were modeled by means of a physical model.
}
The geodetic-geodynamic network (G1) was established with the intention of monitoring recent crustal deformation and serving as the major control network in Israel. In 1996 the network was measured for the first time using GPS. This paper presents the second GPS measurement campaign of the G1 network, held in 2002. It presents the network configuration design and the data processing procedures by commercial and scientific post-processing GPS software, as well as a comparison of the results. Long session duration and medium vector length with strict analysis by the commercial GPS processing software TTC (Trimble Total Control) were found to achieve results that are equivalent to those obtained when using the BERNESE scientific software.
}
For analysing deformation networks, two evaluation strategies are possible. The adjustment of observations of specific epochs can be estimated simultaneously using the one-step analysis. Beside of the vector of parameters of the network points, the parameters of the deformation model are determined. Using the two-step analysis, the geodetic measurements can be processed separately in the first step. This step determines the adjusted co-ordinates of the network points for each epoch. The resulting vectors of these parameters will be used as pseudo measurements in the second step. The parameters of the deformation model are obtained after the second adjustment process. The main advantages of the one-step analysis are that the resulting variance is correctly determined and its use for statistic tests is unproblematic. However, the precision of the epochs is usually estimated only roughly and as a result, the cofactor matrix of the measurements will be incorrect in general. In the two-step analysis, the variance-covariance matrix for the vector of parameters is calculated for every single epoch. These matrices are used for setting up the cofactor matrix of the pseudo measurements correctly. Therefore, in the context of this paper the procedure and the characteristics of the two-step analysis are examined. Special attention is paid to the estimation of the correct variance for this evaluation strategy, because it is the critical parameter for the further investigations of deformations.
}
The performance of geodetic monitoring networks is heavily influenced by the configuration of the measured GPS vectors. As an effective design of the GPS measurements will decrease GPS campaign costs and increase the accuracy and reliability of the entire network, the identification of the preffered GPS vectors for measurement has been highlighted as a core problem in the process of deformation monitoring. An algorithm based on a sensitivity analysis of the network, as dependent upon a postulated velocity field, is suggested for the selection of the optimal GPS vectors. Relevant mathematical and statistical concepts are presented as the basis for an improved method of vector configuration design. A sensitivity analysis of the geodetic geodynamic network in the north of Israel is presented, where the method is examined against two deformation models, the Simple Transform Fault and the Locked Fault. The proposed method is suggested as a means for the improvement of the design of monitoring networks, a common practice worldwide.
}
The existing 2D Cadastre in Israel is not able to facilitate rapid developments in the country. Increasing land shortage also makes necessary an extension into the third dimension of the existing 2D cadastral system, an extension based on the existing 2D cadastral system. A general description and definition of the components of such a system are introduced here. A reinstating/marking technique for the '3D-parcel', based on GPS, is also presented in this article. In addition to land-right registration, one of the objectives of the cadastre is the facilitation of planning and development activities. In recent years, as a result of population increase, economic development and a high standard of living, rapid development has resulted in an almost complete exploitation of land resources, in particular in the northern part of Israel, in the areas of Tel-Aviv and Jerusalem. The increasing population density and land shortage make necessary additional solutions for urban development, such as more efficient utilisation of subterranean and submarine spaces. These solutions will have an impact upon legislation. From a legal point of view, physical evidence in the field (markers) is superior to the content of the cadastral map. Unfortunately, there are no everlasting or indestructible points, thus parcel boundaries must be reinstated again and again. Such legal aspects will cause a slow-down in the future development of space below and above the earth surface.
}
This paper aims at presenting a new perspective of GPS networks, based on principles from graph theory, which are used to describe some connectivity properties of GPS networks. This is possible using a directed, connected graph and an incidence matrix. As the incidence matrix maintains information about the GPS graphy, the fundamental set of independent loops in the GPS network can be read from the incidence matrix. A spanning tree serves as a primary tool in locating the independent loops. According to the loop law the coordinate differences around loops sum up to zero. The measured vectors contain random and gross errors. Hence, if the entire independent loops sums are less than a certain threshold in three components, we can guarantee that there are no gross errors in the observations. The fundamental set of independent loops, based on different spanning trees, is used to detect gross errors in the observations without using adjustment computation. We use a small, simulated network containing gross errors to demonstrate the proposed algorithm.
}
The Galilee-Golan monitoring network was established in the north of Israel in order to measure the relative motion between the two sides of the Dead Sea Rift and the deformation within the area covered by the network. This paper addresses the question of its capability to do so by means of a sensitivity analysis of the network. The paper presents the mathematical and statistical concepts relevant for a sensitivity analysis of a geodetic network and then presents a test of the Galilee-Golan network sensitivity, performed against two deformation models, the Simple Transform Fault and the Locked Fault.
}
This paper focuses on various aspects of datum definitions and datum design for GPS networks. We consider GPS observations as being a major source for positioning future control points. Hence accuracy, reliability, and sensitivity of the datum definition become important. Accuracy measures the impact of random errors, and reliability measures the impact of gross errors in coordinate estimation. Sensitivity provides a quality measure for how well point movements are estimated in time. It turns out that the accuracy and the reliability of GPS networks are independent of the geometric distribution of the network points: this is in contrast to control networks measured by classical methods. We demonstrate that the distribution of datum points does not affect accuracy and reliability while sensitivity does depend on this distribution. We present a number of rules for the distribution of datum points that improve the sensitivity of the datum. The internal reliability does not depend on datum definition. The external reliability, the accuracy and the sensitivity depend on datum definition. It turns out that Baarda's suggestion for measuring the global external reliability is not suitable for GPS networks, another procedure is given.
}
In this paper we investigate how the reliability of geodetic networks can be used as a design criterion. The diagonal of the hat matrix contains useful information; the diagonal elements reflect the reliability of the network. By setting the diagonal elements of the hat matrix less than a given value we design the reliability of the network. We introduce methods to control and design the diagonal of the hat matrix. The methods could be used to design the reliability of new networks or to improve the reliability of an existing network.
}
This paper deals with some aspects of sensitivity design for monitoring networks. At the design stage of a monitoring deformation network postulated velocity field can be made based on prior deformation information. Based on the velocity vector a method of measurement configuration design is given. By the proposed method we use the most affective measurements on the network sensitivity. Taking into consideration the characteristics of the design matrix and postulated velocities a few principles for the geometrical network design are given. The proposed geometrical configuration provides high sensitive network. A small distance network is simulated and its configuration is solved by the proposed method.
}
This paper outlines a strategy for applying the "Set Covering Problem" to the design of measurements by means of GPS. Whenever a set of vectors is to be measured between control network points, the Set Covering Problem can be applied to optimize the design of the measuring sessions by means of a given number of GPS receivers. The solution provides the set of optimal GPS sessions which will measure all vectors in the network. An optimal design of the measuring sessions results in savings of cost and time.
}
During the past ten years GPS has been firmly established as a primary tool for the measurement of high-precision geodetic networks. There may be a tendency in some circles to adopt concepts, methods and approaches to geodetic design which were developed basically for classical geodetic measurements. In this paper we focus on a few aspects of first and second order design of geodetic networks where the measurements are based exclusively on GPS. Modelling and linearization of GPS measurements produce a design matrix which is independent of the positions of the network points. This property which is common to GPS and to ordinary (spirit) levelling makes it possible to implement powerful mathematical tools for the solution of the second order design (SOD) problem and even for some aspects of the first order design (FOD) problem. An interesting interpretation of the elements of a GPS network criterion matrix is proposed. A small network of seven GPS points is simulated and its SOD problem is solved by linear programming.
}